FREE Shipping in the contiguous United States for orders over $250!

F2A3X Frequency to Analog Converter/Tachometer

PN: F2A3X

Regular price $299.00 Sale

 

View Accessories


Description

The F2A3X Frequency to Analog Converter is a DIN rail module that converts a frequency input signal into a proportional analog voltage (0-5Vdc) or current (4-20mA) output. The output signal is electrically isolated from the input signal and input power source, effectively eliminating troublesome ground loops. The input signal can be supplied from a Monarch sensor (measuring RPM for example) or any source of digital signal not exceeding 12 volts. The F2A3X is completely user-programmable using the free downloadable PM Remote Software. A NIST certificate of calibration is included.

TYPICAL USES 

  • Process monitoring over networks
  • Tachometer signal generator
  • QC and R&D
  • Engine performance
  • Signal conditioning
  • Data acquisition
  • Motor or pump monitoring

Features

  • Standard DIN rail mounting
  • Ethernet communications available
  • 5 to 999,990 RPM range (0.083 to 150kHz)
  • Compatible with most speed sensors (TTL)
  • 12 to 24 Vdc input power
  • Alarm set point with optional relay output
  • Pulse repeater output
  • User-configurable
  • View real-time data on PC
  • 4-20mA or 0-5 Vdc scalable output
  • 10 Vdc or 5 Vdc sensor excitation
  • NIST Calibration Certificate included

 


Specifications*

Input Range 5-999,990 RPM speeds below 5 RPM possible with multiple pulses per revolution (0.083 Hz to 150 kHz)
Input Configuration and Voltage Range 1 to 9,999 pulse per revolution or use a scale factor of 0.0001 to 99,999; PC software programmable, TTL input and 1.1V to 25Vdc signals – Internal Jumper for ±1 to ±25Vac
Analog Output Voltage: 0-5Vdc, 5mA max load, Isolated or 4-20mA Isolated, 500 ohm max load, Internal 12V compliance voltage, 16-bit resolution; full scale and offset RPM ranges PC programmable
Accuracy/Resolution 0.005% of full-scale output / 76 micro-volts or 30.5 Nano amps
Output Update Software selectable up to 244 times/sec; dependent on the input frequency
Memory Max and min recall via PC software
Dimensions 1/8 DIN by 3.94" (100mm) deep
Input Power Standard 12-24Vdc, 4.5W max or optional 12Vdc to 24 Vdc isolated 4.5W max
Sensor Excitation 10Vdc @ 60mA standard or 5Vdc @ 60mA optional
Pulse Repeater Output 0-5V TTL compatible, one pulse out for each pulse in; polarity is software selectable
Communications Standard: serial, requires USB interface cable Optional: Ethernet RJ45 or USB type B
Alarm Capability

Optional alarm with relay output

Set-points: high or low alarm limit, latching or non-latching PC Programmable

Alarm Outputs 1 form C relay contact, rated 1A at 115Vac or 230Vac
Alarm Reset Automatic or manual reset; front panel push button or remote reset via PM Remote Software
Environmental

Indoor use only; installation category II per IEC 664

Temperature: -10° to 50° C, operating per IEC 61010-1

Humidity: 80% max to temps up to 31° C, decreasing linearity to 50% RH at 40°C

Electrical Safety Meets EN61010-1:2001, EC low voltage directive 2006/95/EC

 

*Specifications are subject to change without notice.

PM Remote Software

PM Remote Software is a free downloadable Windows-based software application that allows users to quickly and easily customize the configuration of Monarch’s ACT1B, ACT-3X, F2A1X, and F2A3X panel tachometers. Set the mode of operation to RPM, RPS, or Frequency and select the input scale (pulses per revolution). Real-time data can be displayed directly on the PC along with min and max values. Decimal places and display update rate are user-configurable.

Click here for complete details and to download software.

 

Features

  • Allows quick setup of ACT-1B, ACT-3X, F2A1X, and F2A3X
  • Display live data remotely on PC
  • Unit configuration can be saved for reloading in the feature
PM Remote Software Programmable Features

 

PM Remote Software Communications

 

Click here for complete details and to download software.

 


Shipping Codes for F2A3X Frequency to Analog Converter/Tachometer (all models):

Harmonized Tariff Code:  9029205000

Country of Origin:  US

Export Control Classification Number (ECCN):  EAR99

     

Customer Reviews

Based on 2 reviews Write a review